Academic Journal
Features of frictional treatment of the composite NiCrBSi-Cr3 C2 laser clad coating
| العنوان: | Features of frictional treatment of the composite NiCrBSi-Cr3 C2 laser clad coating |
|---|---|
| المؤلفون: | Soboleva, N. N., Makarov, A. V., Zavarzina, E. P., Skorynina, P. A., Malygina, I. Y. |
| المصدر: | Lett. Mater. ; Letters on Materials |
| بيانات النشر: | Institute for Metals Superplasticity Problems of Russian Academy of Sciences |
| سنة النشر: | 2020 |
| المجموعة: | Ural Federal University (URFU): ELAR / Уральский федеральный университет: электронный архив УрФУ |
| مصطلحات موضوعية: | COMPOSITE NICRBSI-CR3 C2 COATING, FRICTIONAL TREATMENT, LASER CLADDING, MICROSTRUCTURE, OPTICAL PROFILOMETRY |
| الوصف: | The authors conducted a comparative analysis of the effectiveness of frictional treatment with a sliding indenter of a NiCrBSi coating and a composite coating formed by laser cladding of a powder mixture of 85 wt.% NiCrBSi and 15 wt.% Cr3 C2 . The criteria were intensive strain hardening, favorable compressive stresses, and low surface roughness. Frictional treatment with an indenter made of cubic boron nitride at a load of 350 N provides less intense deformational hardening of the NiCrBSi-Cr3 C2 coating (microhardness growth from 900 to 940 HV 0.025) than the NiCrBSi coating (from 570 to 850 HV 0.025). This is due to the significantly higher initial hardness of the composite coating, because its structure, in addition to the phases characteristic of the NiCrBSi coating, contains large primary Cr3 C2 carbides, which did not dissolve during cladding, as well as elongated Cr23 C6 carbides, precipitated during cooling from a solid solution supersaturated with chromium as a result of the partial dissolution of Cr3 C2 carbides during cladding. Frictional treatment also results in a lower level of compressive residual stresses (−250 MPa) on the composite coating surface than on the NiCrBSi coating surface (−390 MPa). In contrast to frictional treatment of the NiCrBSi coating, when a smoothed surface with a nano-roughness is formed (Ra = 60 nm), frictional treatment of the composite coating forms a surface with a higher roughness (Ra = 310 nm) due to the creation on the surface of supporting “island frame” of large Cr3 C2 chromium carbides protruding 2 – 5 μm. © 2020, Institute for Metals Superplasticity Problems of Russian Academy of Sciences. All rights reserved. ; The work was performed with the financial support of the Grant from the President of the Russian Federation for young scientists MK-391.2019.8 and at the expense of funds making up the income from the trust management of the target capital for the development of UrFU, formed with the participation of UMMC-Holding Corp, as well as within the state order for ... |
| نوع الوثيقة: | article in journal/newspaper |
| وصف الملف: | application/pdf |
| اللغة: | English |
| تدمد: | 22185046 |
| Relation: | Features of frictional treatment of the composite NiCrBSi-Cr3 C2 laser clad coating / N. N. Soboleva, A. V. Makarov, E. P. Zavarzina, et al. — DOI 10.22226/2410-3535-2020-4-506-511 // Letters on Materials. — 2020. — Vol. 10. — Iss. 4. — P. 506-511.; Final; All Open Access, Bronze; https://www.scopus.com/inward/record.uri?eid=2-s2.0-85097440407&doi=10.22226%2f2410-3535-2020-4-506-511&partnerID=40&md5=b7931dad3e994e607ea33393ad2b9ffc; https://lettersonmaterials.com/Upload/Journals/36991/506-511.pdf; http://elar.urfu.ru/handle/10995/103243; 85097440407 |
| DOI: | 10.22226/2410-3535-2020-4-506-511 |
| الاتاحة: | http://elar.urfu.ru/handle/10995/103243 https://www.scopus.com/inward/record.uri?eid=2-s2.0-85097440407&doi=10.22226%2f2410-3535-2020-4-506-511&partnerID=40&md5=b7931dad3e994e607ea33393ad2b9ffc https://lettersonmaterials.com/Upload/Journals/36991/506-511.pdf https://doi.org/10.22226/2410-3535-2020-4-506-511 |
| Rights: | info:eu-repo/semantics/openAccess |
| رقم الانضمام: | edsbas.632EDC8 |
| قاعدة البيانات: | BASE |
| تدمد: | 22185046 |
|---|---|
| DOI: | 10.22226/2410-3535-2020-4-506-511 |